Effect of ball-milling parameters on the rheological properties of mold powder slurry

In this study, mold powder slurries with high solid loading and low viscosity were prepared during the ball-milling process for improving the homogeneity and mechanical properties of granules after spray-drying. The effect of ball-milling parameters, such as solid loading, binder/dispersant content, and ball-milling time, on the flowability, dispersibility, stability, and rheological behavior of mold powder slurries was systematically investigated by rheology observation and sedimentation tests. As these parameters varied, the slurry exhibited the shear-thinning behavior of a non-Newtonian fluid with a shear rate range of 0–50 s^?1, which was adequately described by the Herschel-Bulkley model. The optimal parameters that optimized the flowability, dispersibility, and stability of the slurry, along with its rheological behavior, were chosen as follows: solid loading, 60 wt%; modified sodium carboxymethyl cellulose binder content, 1.0 wt%; sodium tripolyphosphate dispersant content, 0.5 wt%; ball-milling time, 60 min.     

Exploring the influences of the counterpart materials on friction and wear behaviors of atmospheric plasma-sprayed YSZ coating

Sliding wear behaviors of atmospheric plasma-sprayed Yttria Stabilized Zirconia (YSZ) coating mated with four metallic or ceramic counterparts (Si₃N₄, Al₂O₃, GCr15 and ZrO₂) were investigated. It has been found that YSZ coatings in contact with Si₃N₄ and GCr15 show better tribological performances than the other cases, which is due to the formation of the tribolayer mainly consisting of Si₃N₄ and Fe₂O₃ respectively on the worn surfaces. In the case of YSZ coating-Al₂O₃ and YSZ coating-ZrO₂ tribopairs, the wear debris are more irregular and larger in size, resulting in severe abrasive wear and brittle fracture of debris particles. In particular, the specific wear rate of YSZ coating sliding against GCr15 is negative due to the significant material transfer of the tribo-oxide layer, while that of YSZ coating sliding against ZrO₂ is the highest. Amorphization of the wear particles appears in the four cases due to the repeated mechanical action. It has been demonstrated that the wear of YSZ coating deteriorates with the increased flash temperature between the contact surfaces during rubbing process.     

计及RSC控制的DFIG短路电流直流分量解析表达

现有文献针对计及转子变流器(RSC)控制的双馈感应风电机组(DFIG)定子短路电流解析表达,将定子磁链当作一阶直流衰减分量或忽略功率外环控制。基于DFIG电压、磁链和RSC控制方程,得到定子电流关于定子电压和定子功率的传递函数,提出定子电流的精确解析表达式。基于RSC内、外环PI参数关系,推导直流分量衰减时间常数和角频率关于PI参数的表达式。分析了RSC内外环PI参数对定子电流直流衰减分量的影响。仿真结果验证了解析表达式的准确性,为PI参数选取和保护装置测量、整定提供依据。     

产教融合背景下高职特色专业群“平台+模块”课程体系建设研究

In view of the problems in the construction of characteristic professional groups in higher vocational colleges, the professional group of "intelligent manufacturing" is taken as the research object, and the "platform + module" suitable for the development of the industry will be constructed according to the content of the vocational ability planning courses of the post group. The curriculum system establishes the framework of professional groups, and explores and forms a strategic study to optimize and integrate professional group resources.     

纵轴式掘进机截割头载荷影响因素的仿真分析

针对现有掘进机截割头载荷特性研究方法采用单一影响因素不能全面反映截割头载荷及其波动变化规律的问题,通过分析截割头瞬时载荷,确定了纵轴式掘进机在水平截割工况下截割头载荷的主要影响因素有截割岩石特性、截割头掏槽深度、截割头吃刀深度、截割头转速和截割臂摆速。针对某纵轴式掘进机水平截割工况,采用Matlab对影响截割头载荷的多种因素进行仿真分析,得到了各向载荷及其波动随各因素的变化规律:截割头载荷随着岩壁普氏系数的增大而增加,其中横向阻力增加尤为明显,横向阻力波动程度高于其他方向载荷,且随着岩壁普氏系数的增大呈减小趋势;随着截割头掏槽深度的增加,截割头各向载荷近似呈线性增加,其中升力增加幅度最大,各向载荷波动则随着截割头掏槽深度的增大而减小;随着吃刀深度的增加,截割头载荷总体呈增大趋势,载荷波动程度则随之减小;在截割头转速一定的情况下,截割头载荷均随着截割臂摆速的增加而增大,在同一摆速下,截割头载荷随着截割头转速的减小而增大,横向阻力波动明显高于升力和推进阻力波动,横向阻力和推进阻力波动按截割头载荷规律变化,升力波动则与之相反。截割头载荷波动变化规律与截割头载荷变化规律不尽一致,有时甚至相互冲突。因此,掘进机作业过程中应合理选择截割头掏槽深度、吃刀深度等操作参数和截割头转速、截割臂摆速等运动参数,使各参数相互匹配,以减小掘进机振动,延长使用寿命。     

Analyzing dissipation effects on the non-classicality witnessing by a qubit via the entangled state representation

ABSTRACT

In this paper, we study detection of the state non-classicality for a quantum harmonic oscillator by a qubit in the presence of dissipation effects. We show that dissipation can enhance the effectiveness of the method in case of using the corrected form of the related nonclassicality witness. Such an improvement is attributed to the fact that dissipation leads to probing a surface, instead of a curve, of the complex plane for non-classicality condition on normally-ordered characteristic function.     

煤样多元物性参数在煤与瓦斯突出防治中的应用研究

煤与瓦斯突出是一种复杂的动力现象，突出的类型不同、引起突出的危险因素不同，预测指标对其的敏感性也就不同，选择适应的突出危险性预测敏感指标及突出敏感指标的临界值，研究可靠的突出预测手段和方法来实现对突出危险性的准确预测，是指导突出防治工作的重要技术基础，而为了获得突出敏感指标的临界值就必须对煤的多元物性参数进行实验研究，掌握煤层的各项物化性质，是有效确定防治突出方法体系的关键基础。     

基于气动性能与刚度特性的风力机翼型优化设计

结合翼型泛函集成理论与叶片截面刚度矩阵数学计算模型,提出了风力机中等厚度翼型气动性能与结构刚度特性的一体化设计方法,实现了翼型气动性能与叶片截面刚度特性的同时提高。对考虑叶片截面铺层参数变化设计的WQ-B300翼型与DU97-W-300翼型进行了气动性能与结构刚度特性对比分析,结果表明:相比于DU97-W-300翼型,WQ-B300翼型的气动性能与叶片截面刚度性能均有显著提高,其挥舞刚度和摆振刚度分别提高了6.2%和8.4%,验证了该设计方法的可行性,给风力机中等厚度及大厚度翼型设计提供了一种思路。     

双光束激光焊匙孔动态特征分析

文中研究了高功率单光束激光焊与双光束激光焊过程中匙孔动态特征的差别. 结果表明，单光束激光焊及双光束激光焊接过程中匙孔均处于从产生到湮灭的剧烈波动的过程，不同于单光束激光焊匙孔的形成、长大、维持、缩小、湮灭过程，双光束激光焊的匙孔还存在分离长大及合并缩小的过程；在相同的焊接参数及焊缝具有相同熔深的条件下，双光束激光焊匙孔的波动频率约为单光束激光焊的2/3，单光束激光焊匙孔的开口面积均值约为双光束激光焊匙孔开口面积的1/2，开口面积的波动变异系数约为单光束激光的2倍，即双光束激光焊过程中匙孔较单光束激光焊的具有较高稳定性.     

基于灰色关联度的微孔端面机械密封开启力共性影响参数分析

目前微孔端面机械密封采用的几何参数繁多,缺乏明确物理意义。为找出跨孔型的共性几何参数,基于Fluent多相流空化模型,针对矩形孔、菱形孔、椭圆孔端面机械密封,建立密封间隙流体的三维数值计算模型,计算得到144条开启力数据;在分析开启力和几何尺寸之间的关系、额外开启力产生机制的基础上,提出等效长度和等效宽度2个具有物理意义的几何参数;采用灰色关联度分析法,分析和验证等效长度、等效宽度、方向角、面积比对开启力的影响,发现4个因素对3种微孔密封的间隙流体开启力都有影响,但等效长度与等效宽度的影响较方向角、面积比大。